
The Drawbacks of Mineral and Lime Paint: Who It Suits and Who It Doesn't
Mineral paint is not a cure-all. It is not waterproof, and coloured liquids such as coffee or red wine will soak in; patch repairs are hard to hide completely; there can be slight colour differences between batches; it costs more than latex paint, and the preparation needs more care than with ordinary paint. Knowing this will help you decide whether it is right for your space.
Its strengths are just as clear: matt, with depth of tone, breathable, with at most 1 g/L of VOC. For each point below we explain why it happens and what you can do, drawing on St. Leo's technical data sheets and our own work since 2020.
1. Not waterproof: coloured liquids soak in
The surface of mineral paint is breathable. Moisture can move in and out of the wall, which is how it regulates humidity, but it also means it is not waterproof. Plain water can simply be blotted with a dry cloth; coffee, red wine and other coloured liquids, however, soak in and spread like a drop on fabric and cannot be wiped off. In that case we recommend repainting the whole wall.
Everyday cleaning: once the wall has fully cured (about 30 days), wipe gently with a soft cloth or sponge wrung out in warm water. Avoid scrubbing and do not use cleaning products. When vacuuming nearby, use a soft brush attachment.
If you need a more wipeable surface, choose Lime Paint (washable in itself, EN 13300 class 1), or add Topcoat Five over Dolomite Plaster. Topcoat Five makes the surface wipeable and more resistant to knocks and scratches, but it is still not waterproof.
2. Patch repairs are hard to hide
A small patch will often show. We recommend repainting the whole wall or ceiling with paint from the same batch so the colour and texture match. The lighter the colour, the less a patch shows.
For small damage to Dolomite Plaster, the manufacturer describes a repair method: tape an irregular area around the damage, smooth it with 220-grit sandpaper, apply a thin layer of plaster, let it dry for 12 hours and sand lightly, then apply one thin coat of diluted Topcoat Five and remove the tape while it is wet. For larger damage, re-plastering the whole surface is still recommended.
So keep a little paint from the same batch after the work. Unopened containers keep for 12 months; opened ones, resealed and stored upright, keep for at least 3 months.
3. Colour can vary between batches and materials
Natural raw materials mean each batch differs slightly, and the same colour name on different materials may not look exactly the same. The fixes are simple: order enough from one batch at once; if you need several tins, mix them together first; and use the same material within one space or on adjoining walls. Colour cards and samples are a guide; before the real work, test a small area on site.
4. Preparation matters more than with ordinary paint
Taiwan is humid, with big swings in temperature and humidity through the year. Old walls with efflorescence or leaks need the leak found and fixed first; new timber walls need checking for resin bleed and sealing if necessary. If the preparation is not done well, the wall may show bleed-through or uneven patches of colour, and will need to be re-primed and repainted at extra cost. We recommend leaving this stage to a professional.


5. Does it go mouldy?
Lime Paint is naturally mould resistant, and mineral paints are breathable, which reduces condensation on the wall. But mould usually comes from moisture in the wall itself: efflorescence, leaks, or damp mountain and coastal locations. In Taiwan even ordinary white walls can go mouldy, and mineral paint is no exception. If a wall is damp for long periods, deal with the source of the moisture first and choose an undercoat suited to damp environments; we met exactly this on a project in Beitou, described further down.
6. It costs more than latex paint
Counting materials only, St. Leo costs about NT$1,100 to 2,800 per ping of wall (including one coat of undercoat), depending on the product. The full calculation is in How much does mineral paint cost per ping?
7. Brush marks and variation: character, and a trade-off
Mineral paint leaves brush marks and drying marks, and the same colour will look different when you paint it and when a professional does. People who love it see this as its life; if you want a perfectly flat, even colour, it may take some getting used to.
8. Does it powder?
Not when applied correctly. St. Leo products are developed and tested by the manufacturer and do not powder or chalk. If it does happen, the first thing to check is whether the substrate and priming were done as specified.
9. Places it does not suit
- ◆ Showers and walls in direct contact with water.
- ◆ Outdoors. St. Leo wall paints are for interior walls and ceilings only.
- ◆ Smooth surfaces such as glass and tiles, and metal surfaces.
- ◆ Wood: the manufacturer's data sheets list the wall paints as not for wood. In our experience, timber walls can be painted as long as the substrate is properly sealed and does not bleed; test a small area first. For door frames and cabinets, use the Original Pigments wood and metal finishes.
What does Topcoat Five change?
Topcoat Five is a water-based acrylic topcoat used with Dolomite Plaster. Two coats over the finished, dry plaster make the surface wipeable, more resistant to knocks and scratches, and less sensitive to moisture; the gloss rises from 1 to about 5, and the colour deepens slightly. It also needs about 30 days to cure fully, and it is still not waterproof, so places like showers remain off limits.
Compared with other wall materials
| Latex paint | Cheap, many colours, easy to touch up; but flat colour with no texture or depth. |
| Microcement | Waterproof and hard wearing, works on floors and bathrooms; but expensive and demanding to apply, can crack if the substrate moves, and needs a protective topcoat. |
| Diatomite | Good at regulating humidity and absorbing odours; but soft, marks easily and picks up dirt more readily. |
| Mineral paint | Matt, layered and breathable; but not waterproof, hard to patch, and needs good preparation. |
Every material is a trade-off; the right one depends on what matters most to you. For an overview of decorative paints, see Decorative paint, specialty paint, mineral paint.
Who it suits, and who it doesn't
It suits people who care about the texture of a wall and the way it breathes, who can accept the marks time leaves, and who are willing to get the preparation right.
It doesn't suit people who want a wall that always looks perfect, who need to scrub it often, or whose budget only stretches to a change of colour. Around basins and sinks, where splashes are frequent, if this bothers you we would suggest a damp-proof, waterproof material instead.
Three situations we have met on site
Mineral paint is a breathable, natural material, and its texture always carries a little unpredictability. That is also why the condition of the substrate shows directly on the wall. These are the situations we have met most often over the years.
New homes: a wall that looks sound may not be underneath
In a newly built or newly handed-over home, the walls look flat and complete, but what lies beneath and how it was treated is often impossible to know for sure. To save money, many people skip re-levelling. If you want to apply mineral paint directly, we still recommend an undercoat first. Check too whether the wall is flat: paint is not a filler and cannot make an uneven wall level.
During building work: "mixed materials" inside the wall
If the project is still under construction, we strongly recommend that the owner or designer talks it through with us. The designer or main contractor often knows better than we do where the wall has been repaired: where holes were cut and filled, even where a hole was drilled in the wrong place and patched. Those fillers differ from the original wall, and we call them "mixed materials". If filling with epoxy is not followed by a proper undercoat (cement paint is no substitute for an undercoat), it affects how the mineral paint breathes and absorbs.
Many people ask us why a distinct patch of colour has appeared on their wall. A common reason is that the undercoat was applied only in places, so the wall absorbs unevenly and the colour follows. For an even colour, the undercoat must cover the whole wall; it is also the most reliable way to avoid problems later.
A Dolomite Plaster project in Beitou
We once worked on a Dolomite Plaster project in Beitou. It is a sulphur area and very damp; an ordinary Taiwanese undercoat could not hold, and in the end the wall grew mould.
To be honest, mould on walls is not unusual in Taiwan. In the mountains and in the cities alike, the climate is especially humid, and even ordinary white walls get mould; mineral paint is a breathable material and is affected by its environment too. In the end we did not find the exact cause in this case. After talking it through with the client, the whole space was redone: we switched to an undercoat made for damp bathroom environments and changed the finish to Marble Paint, replanning around the humidity. This time the paint held, and the space returned to how it was meant to look. For similar damp spaces, an undercoat made for damp bathrooms is also an option.
That experience made us more certain: before choosing a paint, the environment the space sits in should be the first thing assessed and discussed.
Still have questions?
For more detail, see the St. Leo Q&A or contact us on LINE. You are also welcome to book a visit to our studio in Anping, Tainan, and feel it for yourself.
To see the finishes in person, work out quantities or talk through your walls, book a visit to our studio in Anping, Tainan, or ask us on LINE.